Product Specs
General Specifications
- Maximum Rating
- 1225 BHP
- Displacement
- 1960.5 in³
- Minimum Rating
- 800 BHP
- Aspiration
- Turbocharged-Aftercooled
- Flywheel and Flywheel Housing
- SAE No. 0 or SAE No. 1
- Flywheel Teeth
- 136
- Stroke
- 6.4 in
- Bore
- 5.7 in
Emissions
- Emissions
- EPA and CARB Non-Road Mobile Tier 2, EPA Marine Tier 2, IMO Tier II, China Stage III
Dimensions
- Length
- 76.1 in
- Width
- 57 in
- Height
- 54.7 in
- Weight
- 5084 lb
Standard Equipment
-
- Air Inlet System
-
- Connections configured for SCAC and ATAAC (Air-to-AirAftercooled) or remote heat exchanger
-
- Control System
-
- ADEM A4 electronic control module
- Electronic governing, PTO speed control
- Customer programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Automatic fuel temperature compensation
- Programmable low and high idle
- Electronic diagnostics and fault logging
- Engine monitoring system
- SAE J1939 broadcast (diagnostic and engine status)
-
- Cooling System
-
- Gear-driven centrifugal jacket water pump — RH
- Integrated thermostat and housing
- Engine oil cooler
- Optional installed transmission oil cooler
- Optional aftercooler and auxiliary water pump
- Optional jacket water heat exchanger
-
- Exhaust System
-
- Exhaust manifold — watercooled
-
- Fuel System
-
- MEUI
- Fuel priming pump
- Fuel transfer pump
- Primary and secondary fuel filter — RH configured for remote mounting (installed RH on shipping plate)
-
- Flywheels And Flywheel Housing
-
- SAE No. 0 or SAE No. 1 flywheel iron housing
- SAE No. 0 or SAE No. 1 flywheel
- Optional transmission adapter
-
- Lube System
-
- Crankcase breather
- Oil filter — RH standard, optional LH or remote mount service
- Oil level gauge — RH standard, optional LH or dual service
- Oil filler — RH standard, optional LH or dual service
- Shallow oil pan, rear sump
-
- Mounting System
-
- Trunnion front support
- Vertical and horizontal pads on rear flywheel housing
-
- Protection System
-
- 24 volt electronic
- Engine overspeed with optional air shut-offs with indicators
- Low engine oil pressure
- Fuel filter restriction
- Fuel temperature
- High engine coolant temperature
- Low engine coolant temperature
-
- General
-
- Vibration damper
- Lifting eyes
- Optional customer wiring connector
- Service tool connector
- Paint — Cat yellow
- Optional two-part primer and mastic caulk
Attachments
-
- Air Inlet System
-
- Air cleaner
- Air inlet adapters
- Turbocharger outlet adapters
- Air lines
-
- Charging System
-
- Battery chargers
- Charging alternators
- Alternator mounting
- Circuit breakers and mountings
-
- Cooling System
-
- Dry charge coolant conditioners
- Thermostat housing
- Coolant level sensor
- Radiator
- Blower fans
- Suction fans
- Fan adapters
- Fan drives
-
- Emissions
-
- IMO certifications
-
- Exhaust System
-
- Elbows
- Mufflers
-
- Fuel Systems
-
- Electric fuel priming pump
-
- Instrumentation
-
- Customer management device
- Interconnect harness
- Gauges and instrument panels
-
- Lube System
-
- Oil pans
- Oil service side
- Oil level gauge
- Oil filters
- Lubricating oils
-
- Mounting System
-
- Structural steel base
- Engine support — front
- Engine support — rear
-
- Power Take-offs
-
- Auxiliary drive
- Damper pulley
- Hydraulics gear pumps
-
- Protection System
-
- Mechanical shutoffs
- Solenoid shutoffs
-
- Starting System
-
- Electric starting motors - 12V, 24V
- Battery sets - 24V
- Battery cable
- Battery rack
- Starting aids
-
- Transmission Arrangement
-
- Transmission water lines
- Transmission cooler