Exterior View
Product Specs
Power Rating
- Power Range
- 260 - 565 ekW
Generator Set Specifications
- Frequency
- 50 / 60
- Minimum Rating
- 260 ekW (325 kVA)
- Maximum Rating
- 565 ekW (706 kVA)
Generator Set Configurations
- Emissions
- EPA Tier 3, IMO II, EU IWW, EU Stage V, China II
Engine Specifications
- Configuration
- In-line 6, 4-Stroke-Cycle Diesel
- Aspiration
- Turbocharged - Aftercooled
- Bore
- 5.7 in
- Stroke
- 7.2 in
- Fuel System
- MEUI
- Oil Change Interval
- 250 / 500 hours
- Governor
- Electronic
- Refill Capacity
- 68
- Cooling
- Heat Exchanger, Keel, Radiator Cooled
- Rotation from Flywheel End
- SAE No. (136 teeth)
Generator Specifications
- Excitation
- SRMP
- Insulation
- Class H
- IP Rating
- IP23 (standard), IP 44 (optional)
- Voltage Regulator
- CDVR (Digital Voltage)
Generator Set Dimensions - Radiator Cooled
- Height
- 94.8 in
- Length
- 55.6 in
- Width
- 66.9 in
- Weight - Approximate
- 13396 lb
Generator Set Dimensions - Keel and Hex Cooled
- Width
- 55.6 in
- Weight - Approximate
- 9747 lb
- Height
- 64.9 in
- Length
- 119.6 in
Standard Equipment
-
- Air Inlet System
-
- Separate circuit after-cooled (SCAC)
- Open Crankcase Ventilation (OCV) system
- Turbocharger, jacket water cooled
- Turbocharger inlet, 152 mm (6 in) OD straight connection
-
- Cooling System
-
- SCAC pump, gear driven, for HEX cooled engines only
- Jacket water pump, gear driven
- SCAC and JW shunt tanks for maintaining proper pump inlet pressures
-
- Exhaust System
-
- Water-cooled exhaust manifold & turbocharger
- Round flanged exhaust outlet
-
- Fuel System
-
- Hybrid fuel line design
- Fuel transfer pump, gear driven
- Front service simplex fuel system
- Manual fuel priming pump
-
- Lube System
-
- Center sump oil pan: Deep 500 hour oil change interval
- Front and top service oil filler locations
- Front service dipstick
- Oil pump, gear driven
-
- Mounting System
-
- Vibration Isolators
- Formed C-channel rails
-
- Control System
-
- Common Interface to all Genset Control Panels
- Programmable Low Idle
- Electronic Diagnostics and Fault Logging
- Electronic Fuel/Air Ratio Control
- Programmable ECM Shutdowns for: High Jacket Water Coolant Temp Low Engine Oil Pressure Engine Overspeed
Attachments
-
- Exhaust System
-
- Dry Elbows
- Water-Cooled Elbows
- Flexible Fitting
- Flange
- Muffler
- Muffler, Spark Arresting
-
- Air Inlet System
-
- Air Inlet Adapter
-
- Charging System
-
- Battery Chargers 10 amp
- Charging alternator 24V 105 amp
-
- Control System
-
- Caterpillar alarm and protection
- EMCP 4.2 control panel
- MGCP III B control panel
-
- Fuel System
-
- Duplex fuel filter – front service
- Fuel cooler
- Primary fuel/water separator
-
- Instrumentation
-
- Generator service side - LH, RH
- Generator terminal box extension
- Load sharing module (option for type approved module)
-
- Lube System
-
- Duplex oil filter
- Sump pump
-
- Protection System
-
- Generator protection - IP44
-
- Starting System
-
- Starting motors - electric and/or air
- Jacket water heaters